How to Identify Simmons Baby Crib Replacement Parts

On this page (7 sections)

1. Where can you find a Simmons crib model number?
2. How do you identify the damaged part?
3. How can you confirm a replacement part fits?
4. Which replacement screw kit matches the original hardware?
5. What should you avoid when replacing a crib part?
6. How do you install and check the replacement?
7. Which Simmons baby crib replacement parts should you choose?

Identify the crib model and damaged component before ordering Simmons baby crib replacement parts. Check the identification label and manual, then match the replacement to the model and the original part's dimensions and connection points.

A crib part can look similar and still fit differently. Start by recording what the label says, where the damaged part sits, and how it attaches.

Where can you find a Simmons crib model number?

Look for the model name or number on the crib's identification label and in its manual. Record the full details, including any date or other identifying information printed with the model.

Check the frame and the mattress support area for a label. If you can't see it without moving or dismantling the crib, don't disturb an unstable frame to search for it.

A missing label doesn't make an uncertain replacement safe to guess. Contact the manufacturer or seller with clear photos of the crib and any remaining label details.

How do you identify the damaged part?

Name the part by its location and job before searching for it. Note whether it's a rail, mattress support, bracket, wheel, or fastener, and record how it connects to the frame.

Take photos of the part from several angles while it's still in place, if safe to do so. If you remove a loose fastener, keep it with the crib and note the hole or joint it came from.

Don't take apart a crib that is unstable or has a structural failure. Keep the child out of it until you can confirm the right repair.

What details matter for replacement hardware?

Match the hardware's diameter, length, thread, head shape, and mating parts. For barrel nuts, brackets, or washers, check those pieces too; matching one screw measurement alone may not be enough.

The general guide to baby crib hardware replacement parts explains what to compare before choosing fasteners. For a wider assortment, see the best crib hardware replacement kit, then verify each size against your crib's manual and original hardware.

The XOOL set includes M6 hex socket screws in five lengths and nuts. Its range can help when the original screw is confirmed as M6, but it doesn't identify the correct size for a Simmons model.

How can you confirm a replacement part fits?

Confirm the replacement against the exact crib model before installing it. Check the part number in the manual or ask the manufacturer or seller to verify compatibility.

Compare the new part with the original: overall length, diameter, shape, hole spacing, and connection points should match where relevant. For hardware, also check whether the thread and head fit the frame and any barrel nut or bracket.

Don't force a part that binds, shifts, leaves a gap, or sticks out. A close fit by appearance isn't confirmation that the part is right.

If you have a convertible model, the steps in our guide to convertible crib parts can help you identify parts by model and crib configuration. For another brand-specific example, see Graco convertible crib parts.

What if the crib model is discontinued?

Ask the manufacturer or seller whether an approved part remains available for that model. Share the model number and photos rather than relying on a generic search result or a part that merely looks similar.

If no one can confirm compatibility, don't improvise with drilled holes, extra washers, or mixed hardware. A crib is a safety-critical piece of furniture, so an uncertain structural repair is a reason to stop using it until you get qualified guidance.

Which replacement screw kit matches the original hardware?

Choose a screw kit only after you know the required size and connection type. These assortments offer different ranges, so compare them with the original hardware rather than assuming any crib kit fits.

The Glarks set includes M6 socket cap bolts in 15, 25, 35, 45, 55, 65, and 75 mm lengths, plus M6 barrel nuts and an Allen wrench. Check that the length and barrel nut match your original hardware.

The Lhazemu kit includes M6 bolts in 40, 50, 60, 70, and 80 mm lengths, M6 barrel nuts, and a hex key. Its range differs from the Glarks and XOOL assortments, so measure first.

Neither kit confirms compatibility with a Simmons crib by itself. Stop if the original hardware's measurements or connecting parts are unknown.

What should you avoid when replacing a crib part?

Don't substitute a part based only on appearance or a broad “fits most cribs” description. A wrong fastener or structural component can leave a joint loose or prevent the crib from assembling as intended.

Avoid forcing screws, combining unrelated hardware, or changing the frame to make a part fit. Don't use a damaged crib while you wait for a replacement, and don't rely on accessories to compensate for a structural problem.

Accessories such as best baby crib accessories are separate from repair parts. They don't replace a missing rail, broken support, or failed fastener.

How do you install and check the replacement?

Follow the crib's instructions and use only the confirmed replacement part. Assemble the joint as directed, using the specified hardware and tools.

After installation, check that the part sits flush and the connection is secure without forcing it. Recheck the assembly according to the manual, and stop if anything shifts, gaps, or feels unstable.

If you need to identify hardware for a different brand, the guides to Dream On Me crib hardware and Dream On Me crib replacement parts cover those model checks. A monitor's replacement component follows a different process, as explained in our guide to the VTech baby monitor parent unit.

Which Simmons baby crib replacement parts should you choose?

For Simmons baby crib replacement parts, use the model number and manual to confirm the exact component first. Choose a hardware assortment only when its measurements and connecting pieces match the original.

XOOL offers five M6 screw lengths, Glarks adds seven M6 lengths and barrel nuts, and Lhazemu covers five different M6 lengths with barrel nuts. Pick the set that matches your confirmed hardware, or contact the manufacturer when the model or part remains uncertain.

Frequently asked questions

How do I find my Simmons crib model number?

Check the crib's identification label and manual for a model name or number. Look on the frame in places such as the mattress support area or underside, without moving or taking apart an unstable crib.

Record the label details and contact the manufacturer or seller if the label is missing.

Can I use universal crib screws on a Simmons crib?

Only use replacement screws that match the original size, thread, length, head, and connecting hardware. A kit described for cribs may still not fit your model.

Compare the manual and original fastener, and don't use a bolt that binds, sits loose, or protrudes.

What should I do if I can't identify a damaged crib part?

Stop using the crib if a structural part is damaged or missing, and keep the child in a safe sleep space. Photograph the part and its location, record the model number, and ask the manufacturer or a qualified repair professional to identify an approved replacement.

Can I replace a crib rail with a similar-looking part?

No. A similar shape doesn't confirm that a rail fits the crib or locks into its frame safely.

Use only a replacement confirmed for the exact model, and follow the crib's manual.

If you can't confirm the part, don't use the crib until you get guidance.